Before sending a failed hard drive to a data recovery lab, write down the drive’s details and how it failed, and pack the drive in soft, anti-static material so that it is jolted as little as possible in transit. The more complete the information we receive up front, the faster we can recover the data you need.
About the drive
- Manufacturer and exact model, firmware version, date of manufacture and serial number. For Western Digital drives, give the DCM code; for Hitachi (IBM), the MLC code; for Seagate, the firmware and configuration (Config) code.
- Capacity (MB, GB or TB).
- Operating system and version, and the file system (for example FAT, NTFS, Ext3), with the number of partitions and their approximate sizes.
- Whether the drive was part of a RAID array or used on its own.
If possible, photograph the drive from the top, bottom and sides and email the photos before sending the drive. The model, firmware and other label details must be clearly legible. This helps us choose the right tools and, if needed, a donor drive more quickly.
Will a donor drive be needed?
Sometimes, usually with a hardware fault, recovery needs a “donor” drive of the same model, with the same firmware (Seagate, Toshiba), MLC (Hitachi) or DCM (WD). Whether a donor is really needed depends on the case, so ask us before sending one. If your organisation bought several drives or computers of the same model at the same time, please let us know.
About the failure
- A description of the problem in your own words: the drive is not detected by the BIOS, it makes unusual noises, partitions are not visible, files were corrupted or deleted by a virus, a file was deleted by mistake, and so on. It also helps to say:
- whether the motor spins up and what sounds the drive makes;
- whether the BIOS detects the drive and shows the model correctly;
- whether the operating system sees the drive;
- how the drive behaved before it failed;
- whether the drive was dropped or exposed to water, fire, lightning or an electrical discharge, and whether there is visible damage (dents, cracks, burnt chips).
- The files and folders you need most: exact names with folder paths, file extensions and the programs used to open them, approximate size, and which are the most urgent.
- Your deadline: when you need the data back, and whether it is in constant use (for example accounting data).
Hardware, software and passwords
- Controllers and adapters used with the drive (for example the RAID controller model). If the drive was used with a special adapter or controller, we may need that too. Also list any special drivers or programs (data security, mounting) and any passwords that may be needed during recovery.
- Software for checking files. Sometimes, though not always, we need the application the files were used with to check the recovered files for consistency (for example a Navision database). For checking and recovering Microsoft Outlook PST files we have our own specialised software.
What has already been tried
- What steps were taken at home or by other companies to recover the data: was the drive opened, and if so, was that done outside a clean room? What diagnosis did another company give, and which parts did it replace or try to replace?
- Bad sectors and defragmentation: when the drive was last scanned for bad sectors or defragmented, and roughly how many bad sectors were found.
Warranty, destination media and type of service
- Warranty and opening. Tell us whether the drive is still under warranty and whether the warranty labels are intact. If the drive has to be opened, its warranty will be void, so we need your consent.
- Where to write the recovered data. If you supply your own media, its capacity must be at least that of the failed drive.
- Forensic work. If the recovery is part of a criminal investigation or follows a court order, tell us in advance.
- Type of service: data recovery (including password removal and logical recovery), repair of the media without preserving the data, or destruction of the data and the media.
How to pack the drive
Packing matters most when the drive is physically damaged, for example when the heads have failed. Every jolt in transit can cause further damage.
- The manufacturer’s original packaging is best.
- Otherwise, use a sturdy box at least twice the size of the drive.
- Surround the drive with soft, shock-absorbing material such as foam or bubble wrap, at least 5 cm thick on every side.
- Use anti-static packaging. Avoid materials that attract static electricity, such as Styrofoam.
- Keep the drive away from magnetic fields.
- Choose a shipping method with as little shaking and reloading as possible.
Email us the drive and failure details, and put a printed copy in the box with the drive.
If the drive got wet or was in a fire
Do not try to dry the drive. If it was in water, pack it with a damp sponge so that it does not dry out completely: the chances of recovery are higher if our engineers receive the drive before it has dried. A fire-damaged drive should also be sent as it is.
What happens when the drive arrives
After the initial diagnosis we give you a list of the files that can be recovered from your drive, so you can see in advance whether the data you need has survived.